Fpt Laminated Foil Fire Performance Testing BS476-6 Tester

• After-sales Service: Online Training, Reply Customer′s Question in 12h
• Warranty: 365 Days
• Item Name: Laminated Foil Fire Testing BS476-6 Tester
• Model NO.: FPT
• Application: Measure Fire Propagation Inde of Building Material
• Reference Standards: BS476-6, BS476 Part 6
• Application Field: Building Material, Railway, Marine, Cable, etc.
• Apparatus Dimension: 400mm (W) X 600mm X (H) X 300mm (D)
• Features: Good Design BS476-6 Tester for Foil Fire Testing
• Controller: 400mm (W) X 500mm X (H) X 400mm (D)
• Gas Supply: G112
• Flow: 0 to 5 Nl/Min
• Pressure: 1kpa
• Power Supply: 220V, 10A, 50Hz
• Operation Method: Through Computer
• Display: on Computer
• Language: English
• OEM Service: Yes, Available
• Transport Package: BS476-6 Tester Is Packed in Veneer Casse
• Specification: 400mm (W) x 600mm x (H) x 300mm (D)
• Trademark: DELTA
• Origin: China
• HS Code: 9031809090
• Production Capacity: 100 Sets BS476-6 Tester / Month
• Package Size: 95.00cm * 60.00cm * 106.00cm
• Package Gross Weight: 105.000kg

Product Description

FPT Laminated Foil Fire Performance Testing BS476-6 Tester

Product Description

1. BS 476-6 is a test method of measuring the flame propagation properties of materials, primarily for fire protection performance evaluation of the walls and ceilings. measurement results are expressed as an index of flame propagation.
2. During the test, the specimen is exposed to the tubular torch, heat release of the lamp is 530J / S. 2 minutes and 45 seconds later, the two electric heater was adjusted to 1800 watts in total, 5 minutes after starting the test, reduced the power to 1500 watts, keep the power not changed until finishing the experiment, the total test time is 20 minutes.
3. To assess the flame propagation properties of the material to be tested in BS476-6, thermocouple continuous recording chimney temperature and room temperature difference, and compared the results with the calibration curve, calibration curve based on the provisions of the density of asbestos - cement slab in the same measured way. 
4. Comparing the temperature difference value of two curves which were measured at the same time. In the first three minutes of the test, take the temperature difference value every 30 seconds; in the following 4-10 minutes, take the temperature difference value every minute. In the last 11-20 minutes, take the temperature difference value every two minutes. The flame spread index of these three periods is calculated according to the formula.
5. I is the value of the sum of the three periods of the flame spread index. The higher the I value, the lower the material flame retardant, 0 grade material I≤12.

Product Parameters

No.	Name	Roofing Materials BS476 Part 6 Fire Propagation Index Testing BS476-6 Apparatus
1	Dimension	Apparatus: 400mm (W) x 600mm x (H) x 300mm (D) Control module: 400mm (W) x 500mm x (H) x 400mm (D)
2	Weight	46kg
3	Power supply	230 volts Nominal 10 Amps
4	Ambient temperature	Operating 10^OC to 35^OC
5	Gas supply	The gas supply specified in the Standard is Standard test gas G112, as specified in BS 4947
6	Flow	Gas flow for the burner adjustable from 0 to 5 nl/min
7	Pressure	1kPa

Reference Standards

BS 476 Part 6 A1: 2009

Features

1. Stainless steel cabinet support frame
2. Calcium silicate board combustor
3. All three sample holders are stainless steel parcel
4. 2 sets 1000W quartz radiation devices to provide thermal radiation to samples
5. T-type burner supplies flame combustion to the sample
6. Thermocouple continuous recording temperature and room temperature difference value in chimney
7. The power output is automatically controlled according to the test of time
8. The computer automatically processes the data and prints the test report

Application Field

• Building Materials;
• Rail;
• Others;

Data Acquisition System:

1. Prompted software interface
2. Data recording and display of cowl temperature against time
3. Data recording and display of ambient temperature against time
4. Display of power value in kW
5. Calibration routine
6. Calculation of output rise and calibration value

Please contact us for a quotation and more technical information.